Short Answer
Chopped strand mat (CSM) is a non-woven fiberglass reinforcement made from short glass strands, a few centimetres long, laid in random directions and held together by a light binder. Because the fibres point every way, the mat gives roughly equal strength in all directions across the sheet. It is the cheapest and easiest fiberglass reinforcement to lay up by hand, and it is often used together with woven roving, a heavy woven fabric of continuous strands.
What is chopped strand mat made of?
Chopped strand mat is made of E-glass strands chopped from continuous roving, scattered onto a moving belt, and bonded with a small amount of binder. The binder holds the mat together during handling, then dissolves in the laminating resin so the fibres can follow the mould shape.
A typical data sheet from German supplier DD Composite gives a clear picture of the material (DD Composite fiberglass mat TDS, 11/2022):
- Glass type: E-glass with a silane coupling agent.
- Strand length: 50 mm.
- Filament diameter: 12 µm.
- Binder: powder or emulsion, both “easily soluble in styrene.”
- Moisture content: 0.2% maximum.
The random fibre layout is what makes CSM different from every woven fabric. It has no weave pattern, no preferred direction, and no threads to unravel when it is cut or torn.
Chopped strand mat weights and what they mean
CSM is sold by area weight: grams of glass per square metre. Heavier mats build thickness faster but need more resin. The table below uses the DD Composite figures for resin use and cured laminate thickness per layer.
| Mat weight (g/m²) | Approx. US equivalent | Binder offered | Resin needed (kg/m²) | Laminate per layer |
|---|---|---|---|---|
| 150 | 0.5 oz/ft² | Powder | 0.4–0.5 | about 0.4 mm |
| 225 | 0.75 oz/ft² | Powder | 0.7–0.9 | about 0.5 mm |
| 300 | 1 oz/ft² | Powder or emulsion | 0.8–1.0 | about 0.7 mm |
| 450 | 1.5 oz/ft² | Powder or emulsion | 1.0–1.3 | about 1.0 mm |
| 600 | 2 oz/ft² | Powder | 1.3–1.7 | about 1.3 mm |
Watch the units when comparing suppliers. In the US, mat is rated in ounces per square foot, while woven fabrics are rated in ounces per square yard. One ounce per square foot is about 305 g/m², so “1.5 oz mat” is the same product as 450 g/m² mat. Note too that the resin figures run at roughly two to three times the glass weight, so a mat laminate is mostly resin.
Emulsion binder vs powder binder
The binder decides how quickly the mat wets out and how well it drapes. Both types dissolve in styrene-based polyester and vinyl ester resins, but they behave differently in the mould:
- Emulsion-bound mat: the binder is sprayed on as a liquid. UK supplier Cromar describes its emulsion mat as bonded with a “styrene-soluble emulsion binder” that gives fast wet-out and easy air removal (Cromar PRO GRP CSM TDS). It suits general polyester lay-up.
- Powder-bound mat: the binder is a fine powder fused onto the strands. DD Composite offers its lightest and heaviest mats (150, 225 and 600 g/m²) only with powder binder. Check that the binder suits your resin system before switching types.
- Binder content: measured as loss on ignition. DD Composite lists about 6.5% for 300 g/m² mat and 4.5% for 600 g/m² mat.
Epoxy is the exception. Epoxy contains no styrene, so it does not dissolve standard binders. The mat stays stiff, will not drape into tight curves, and can cure cloudy. For epoxy work, a stitched fabric is usually the better reinforcement.
What is woven roving?
Woven roving is a heavy fiberglass fabric made by weaving thick bundles of continuous glass strands in a coarse basket pattern. Because the strands are continuous and run in two directions (0° and 90°), it is much stronger than mat in those directions, but it leaves a pronounced weave texture and gaps between bundles.
That is why the two materials are almost always used together. Mat fills the gaps and bonds layers; woven roving adds strength and stiffness. A classic hand lay-up schedule alternates them: mat, roving, mat, roving.
Chopped strand mat vs woven roving
The difference comes down to fibre length and layout. The comparison below summarises how they behave in a laminate.
| Property | Chopped strand mat | Woven roving |
|---|---|---|
| Fibre form | Short strands, random directions | Continuous strands, woven at 0° and 90° |
| Strength | Moderate, equal in all directions | High along the weave directions |
| Resin demand | High | Lower |
| Drape | Conforms easily once wetted | Stiffer, bridges over sharp corners |
| Surface | Smooth, no pattern | Strong weave texture |
| Interlayer bond | Good, fibres nest into neighbours | Poor on its own; needs mat between layers |
| Cost per kg | Lower | Higher |
| Typical role | Skin layers, bulk, bonding layers | Structural strength layers |
Some suppliers sell “combo mat,” which stitches a layer of CSM to a layer of woven roving. It saves lay-up time on large flat parts while keeping the same mat-roving sequence.
What is chopped strand mat used for?
CSM is used wherever a part needs bulk, a smooth surface or multi-directional strength at low cost. Common uses include:
- Skin coat behind gelcoat: a mat layer directly behind the gelcoat stops the weave of heavier fabrics from printing through to the surface.
- Moulds and tooling: moulds are often built from several layers of mat because it is stable and easy to shape.
- Boat hulls, tanks and pools: mat-and-roving laminates are the traditional hand lay-up construction.
- Repairs and tabbing: mat torn into strips bonds bulkheads and patches damage.
- Roofing and lining: GRP roofing systems use mat with polyester resin over decking.
Mat is a poor choice where weight matters. Its high resin content makes it heavier for a given strength than fabric laminates.
How to lay up chopped strand mat
Hand lay-up with CSM follows a simple sequence. Work in a ventilated space and wear gloves, eye protection and a respirator rated for styrene vapour and glass dust.
- Prepare the mould: clean it and apply release agent, building up several coats on a new mould.
- Tear the mat to size: tearing rather than cutting leaves feathered edges that blend into the next piece without a hard seam.
- Apply a resin coat: brush or roll catalysed resin onto the mould or gelcoat.
- Lay the mat and wet it through: stipple resin in until the binder softens and the mat turns translucent.
- Roll out air: use a ribbed roller to consolidate the layer and remove bubbles; white patches mean dry fibre.
- Add further layers: overlap joints and stagger them between layers.
- Trim at the green stage: cut edges with a knife once the laminate is firm but not fully hard, then let it cure before demoulding.
Is chopped strand mat used in FRP grating and profiles?
It depends on the process. Hand lay-up and some moulded products use mat-type reinforcement, but pultruded structural profiles use continuous materials, not chopped mat.
- Pultruded profiles: continuous roving runs along the length, combined with continuous strand mat for crosswise strength. Strongwell describes its EXTREN shapes as “a combination of roving and continuous strand mat” (Strongwell Design Manual, Section 3). Continuous strand mat uses long swirled strands, so it holds together as it is pulled through the die.
- Molded grating: continuous glass roving is laid in layers in a mould to form the bars, giving strength in both directions.
- Surfacing veil: a thin synthetic veil on the outside of pultruded parts creates a resin-rich layer for corrosion and UV protection.
For buyers this matters because reinforcement type drives strength. Strongwell notes that an all-roving rod has higher lengthwise tensile strength than mat-and-roving shapes, so the reinforcement schedule should be on the data sheet. The differences between the two FRP processes are explained in pultrusion vs molding and molded vs pultruded FRP grating.
What to check on a chopped strand mat data sheet
If you buy CSM for production, compare suppliers on the measured values, not the nominal weight alone:
- Area weight and tolerance: tested to ISO 3374; DD Composite quotes ±5% on the roll average.
- Binder type and solubility time: emulsion or powder, and how fast it dissolves in styrene.
- Loss on ignition: binder content to ISO 1887.
- Moisture content: to ISO 3344; wet mat causes poor cure and white spots.
- Breaking strength: dry tensile strength to ISO 3342, which shows whether the mat will tear during handling.
- Shelf life and storage: Cromar lists 12 months in unopened packaging, stored cool and dry.
FAQ
Is chopped strand mat stronger than fiberglass cloth?
No. Woven cloth and roving are stronger in their fibre directions because their strands are continuous. Mat is weaker but equal in all directions, cheaper, and better at building thickness.
Can you use chopped strand mat with epoxy?
You can, but standard binders do not dissolve in epoxy, so the mat stays stiff and may cure cloudy. Use polyester or vinyl ester with CSM, or switch to a stitched fabric for epoxy.
What does 450 g/m² mean on chopped strand mat?
It means each square metre of mat contains 450 grams of glass, roughly the same as 1.5 oz per square foot.
What is the difference between chopped strand mat and chopped strands?
Chopped strands are loose cut fibres, used in spray-up guns or compounded into plastics. Chopped strand mat is those strands bonded into a sheet you can handle and lay in a mould.
Looking for finished fiberglass products?
Machs manufactures molded grating, pultruded FRP profiles and handrail systems. Ask us for the reinforcement and resin details of any product you are considering. Contact Machs.