Short Answer
Carbon fiber is stronger, about three times stiffer and around 30% lighter than glass fiber, which makes it the choice when weight and rigidity decide the design. Fiberglass costs far less, stretches more before breaking, and does not conduct electricity, which is why it dominates industrial products such as grating, handrails, tanks and cable supports.
Carbon fiber vs fiberglass at a glance
The fibres themselves show the difference most clearly. The table compares a standard-modulus carbon fibre (Toray T700S) with standard E-glass, using the manufacturers’ published data, plus aramid (Kevlar 49) for reference.
| Fibre property | Carbon fibre (T700S) | E-glass fibre | Aramid (Kevlar 49) |
|---|---|---|---|
| Tensile strength | 4,900 MPa | 3,815–3,830 MPa | 3,200 MPa |
| Tensile modulus (stiffness) | 230 GPa | 78–79 GPa | 125 GPa |
| Density | 1.80 g/cm³ | 2.60–2.62 g/cm³ | 1.45 g/cm³ |
| Elongation at break | 2.1% | 3% | 2.5% |
| Strength ÷ density | about 2,720 | about 1,460 | about 2,210 |
| Modulus ÷ density | about 128 | about 30 | about 86 |
| Electrical behaviour | Conductive | Insulator | Insulator |
Sources: carbon fibre from the Toray T700S data sheet; E-glass from the Owens Corning higher performance composites sell sheet (pristine fibre at 22 °C); aramid from Princeton University’s fibre properties table. The two ratio rows are our calculation from these figures. Fibre values are far higher than finished-part values, because a composite is part resin.
What is the difference between carbon fiber and fiberglass?
The difference is the fibre. Fiberglass uses fibres drawn from molten glass; carbon fibre uses fibres made mostly of carbon, produced by heating a precursor fibre (usually polyacrylonitrile) at very high temperatures. Toray lists carbon content above 93% for T700S.
In both cases the fibre is only half the story. The finished material is a composite: fibres held in a resin such as epoxy, vinyl ester or polyester. That means “carbon fiber” parts are really carbon fibre reinforced polymer, and “fiberglass” parts are glass fibre reinforced polymer (FRP or GRP). If you are new to the idea, what is FRP explains how the fibre and resin share the load.
Is carbon fiber stronger than fiberglass?
Yes, but by less than most people expect. On the datasheet figures above, T700S carbon fibre is about 28% stronger in tension than E-glass (4,900 vs about 3,820 MPa).
The gap widens once weight is counted. Carbon fibre is roughly 30% less dense, so its strength per kilogram is about 1.9 times that of E-glass. This is the number that matters in aircraft, race cars and bicycles, where every kilogram saved pays back.
For a static industrial structure that is not weight-critical, the raw strength difference rarely decides the choice. Fiberglass parts are simply made a little thicker.
Which is stiffer: carbon fiber or fiberglass?
Carbon fibre is much stiffer. Its tensile modulus of 230 GPa is close to three times the 78–79 GPa of E-glass, and per kilogram it is more than four times stiffer.
Stiffness controls deflection, and it is often the real limit in composite design. Toray’s own composite data shows what this means in a finished part: a unidirectional T700S/epoxy laminate at 60% fibre volume reaches a tensile modulus of 134 GPa. A pultruded fiberglass structural shape, which mixes lengthwise roving with crosswise mat, has a full-section modulus of 2.6–2.8 × 10⁶ psi, about 18–19 GPa (Strongwell Design Manual, Section 3).
The two figures come from different fibre layouts, so treat them as an illustration rather than a like-for-like test. The conclusion still holds: where a long span must not bend, carbon fibre gives far more stiffness for the weight.
Which weighs less?
Carbon fibre is lighter: 1.80 g/cm³ against 2.60–2.62 g/cm³ for E-glass, about 31% less. Finished laminates differ by less, because both contain resin, which has a lower density than either fibre.
Both are light compared with metal. A pultruded fiberglass shape has a density of about 1.7–1.9 g/cm³ (Strongwell lists 0.062–0.070 lb/in³), roughly a quarter of steel. For handrails, grating and platforms, fiberglass already delivers most of the weight saving that matters for handling and installation.
Is fiberglass tougher than carbon fiber?
Fiberglass is generally more forgiving. E-glass stretches about 3% before it breaks, against 2.1% for T700S carbon fibre, so glass laminates absorb more energy and show visible damage before they fail.
Carbon fibre parts are stiff right up to failure and can break suddenly under impact. Damage may also be hidden inside the laminate. That is one reason fiberglass is preferred for walking surfaces, handrails and equipment guards that take knocks from tools and trolleys.
Which conducts electricity?
Carbon fibre conducts electricity; fiberglass does not. Toray lists an electrical resistivity of 1.6 × 10⁻³ Ω·cm for T700S, which makes it a conductor. Glass fibre composites are insulators: Strongwell lists a dielectric strength of 35 kV/in lengthwise for its fiberglass shapes.
This single property rules carbon fibre out of many industrial uses:
- Substations and rail: walkways, handrails and cable troughs near live parts must not conduct.
- Ladders and access equipment: fiberglass rails are chosen because they do not conduct.
- Radio and radar: glass fibre lets signals through, so it is used for antenna covers; carbon fibre blocks them.
- Galvanic corrosion: carbon fibre touching aluminium or steel in a wet environment can drive galvanic corrosion of the metal, so joints need insulation. Glass fibre does not create this risk.
The electrical side is covered in detail in is fiberglass conductive.
Thermal expansion and temperature
Carbon fibre barely changes length with temperature. Toray lists a slightly negative coefficient of thermal expansion for T700S fibre, −0.38 × 10⁻⁶ /°C, so well-designed carbon laminates are almost dimensionally stable. That suits telescopes, measuring equipment and precision tooling.
Fiberglass expands more. Strongwell lists 7 × 10⁻⁶ in/in/°F lengthwise for its pultruded shapes (about 12.6 × 10⁻⁶ /°C), close to that of steel. For long runs of handrail or grating this means the usual expansion allowances apply.
In both materials, the resin sets the upper temperature limit, not the fibre. The resin choice therefore decides heat resistance for either material.
Corrosion and chemical resistance
Both fibres resist corrosion far better than metals; in practice, the resin decides chemical resistance. Vinyl ester resins handle acids and bases, isophthalic polyester handles most acids, and epoxy is common in carbon fibre parts.
Because the fibre makes little difference here, industrial buyers select fiberglass with the right resin rather than paying for carbon fibre. The resin and corrosion guide shows which resin suits which chemical.
How much more does carbon fiber cost?
Carbon fibre costs many times more than glass fibre. Prices vary with grade and market, but the gap is structural:
- Raw material and energy: carbon fibre is made from a precursor fibre that is stabilised and carbonised at high temperature, a slow, energy-heavy process. Glass fibre is drawn from melted mineral raw materials in large continuous furnaces.
- Fewer producers: far fewer companies make carbon fibre than glass fibre, which is produced in large volumes in many countries.
- Processing: carbon parts often use epoxy, prepreg and autoclave curing; fiberglass parts can use lower-cost polyester and vinyl ester with pultrusion, moulding or hand lay-up.
For a walkway or handrail, the price difference buys stiffness and weight savings that the application does not need.
Fiberglass vs Kevlar
Kevlar (an aramid fibre) sits between the two. It is the lightest of the three at 1.45 g/cm³, with stiffness between glass and carbon, and it is exceptionally tough, which is why it is used in body armour and cut-resistant gloves.
Aramid has drawbacks for structural use. It is weak in compression, absorbs moisture, degrades in sunlight unless protected, and is hard to cut and machine. It is used where impact or penetration resistance matters most, not for general structures.
When to choose carbon fiber or fiberglass
Choose by the property your design cannot do without. Each fibre has a clear set of jobs:
Choose carbon fiber when
- Weight saving pays back directly, as in aircraft, drones, race cars and robotics.
- Stiffness limits the design, such as long thin arms, booms and shafts.
- Dimensional stability across temperature is critical.
- The budget supports a premium material.
Choose fiberglass when
- The part must not conduct electricity or must pass radio signals.
- It will take impact and abuse, such as walkways, stairs and guards.
- It sits in a corrosive plant and the resin can be matched to the chemicals.
- Large volumes or large areas make material cost decisive.
Most industrial access and support structures fall into the second list. That is why fiberglass grating, handrail systems and pultruded profiles are glass-fibre products. For the comparison with metals, see fiberglass vs steel vs aluminum.
FAQ
Is carbon fiber stronger than steel?
Per kilogram, yes, by a wide margin. Carbon fibre composites are also much lighter, but a steel section of the same size can still be stiffer than a lightly reinforced composite, so the comparison depends on the part.
Can you mix carbon fiber and fiberglass?
Yes. Hybrid laminates place carbon fibre where stiffness is needed and glass fibre elsewhere to cut cost and add toughness. Both bond with the same resins.
Does carbon fiber rust?
No. Carbon fibre does not rust, but it can cause galvanic corrosion in metals it touches when moisture is present.
Why are fiberglass ladders used instead of carbon fiber?
Because glass fibre does not conduct electricity. A carbon fibre ladder could carry current from an overhead line, so it would defeat the purpose of a non-conductive ladder.
Specifying non-conductive structures?
Machs manufactures glass-fibre FRP profiles, grating and handrail systems for electrical, chemical and marine sites. Send your drawings and we will propose a section and resin. Contact Machs.